How to Recover Data from SSD Drive Quickly

Solid-state drives not only offer faster read and write speed than traditional hard disk drives, but also are less likely to fail due to mechanical failure. That’s because SSDs does not have mechanical parts.

However, this does not mean that your SSD will not fail or lose data. And it’s hard to recover data from SSD, but not impossible. The success rate varies greatly depending on whether the TRIM command is enabled.

Quick Navigation:

• How Does TRIM Affect SSD Data Recovery?
• How to Increase SSD Data Recovery Success Rate
• How to Recover Data from SSD in Windows 10 or 11
• Approach Data Recovery Service When Necessary
• Common Signs of SSD Corruption
• How to Fix a Failed SSD
• How to Keep SSD Always in Health Status
• Frequently Asked Questions about SSD Data Recovery

How Does TRIM Affect SSD Data Recovery?

The SSD TRIM is an Advanced Technology Attachment (ATA) command to inform the operating system which data blocks are unused and can be deleted or overwritten. You can then directly write data in these blocks without waiting for the block to zero, making SSD faster.

Upon deleting data, the TRIM command will be triggered and immediately "zero out" or erase all deleted data unless you act promptly. However, in the following situations, the TRIM does not have enough time wipe out the paths and make it possible to recover data from SSD drive.

• unplug SSD quickly after deleting files
• power failure
• software error
• file system corruption
• sudden partition loss
• ...

How to Increase SSD Data Recovery Success Rate

To ensure you can successfully recover data from SSD disk, there are some useful tips you can follow:

• Disconnect the SSD from your computer immediately after noticing data loss on it. You can reconnect it to another computer or keep your machine shut down until you are ready to recover data.
• Disable the TRIM command in SSD disk.
• Install data recovery software on a different drive. Installing software on the same drive could overwrite the previous data and making data recovery impossible.
• Use the best SSD data recovery software. SSD data recovery is a time-sensitive process, so you may only have one change to undelete your files. Usually, it means you will speed some money for it.

Steps to Disable TRIM on Your SSD

Step 1. Input cmd in the search box and select Run as Administrator.

Step 2. Type fsutil behavior set DisableDeleteNotify 1 in the Command Prompt window and press Enter. If you receive the “NTFS DisableDeleteNotify = 1 (Enabled)” message, it means the TRIM is disabled.

Step 3. You can always enter fsutil behavior query DisableDeleteNotify to check the current TRIM status. If the DisableDeleteNotify value is 1, the TRIM is disabled.

Tip: If you enable TRIM after recovering, please replace 1 with 0 in the command fsutil behavior set DisableDeleteNotify. 

How to Recover Data from SSD in Windows 10 or 11

Although the TRIM command affect greatly SSD data recovery, you still can recover data from SSD disk with best SSD data recovery software. MyRecover is a great choice because of its advanced scan engine and robust data recovery algorithm.

• Has a high success rate and fast recovery.
• Recover lost Word document, PPT, Excel, photos, videos, audios, Emails, webpages, compressed files, and more than 200+ file types.
• Keep the original file name, format, quality and location after recovering data from SSD drive.
• Support various SSD types (SATA, M.2, NVMe, PCIe, etc) and brands, such as, WD, Toshiba, Seagate, Samsung, and more.
• Apply to comprehensive data loss scenarios in Windows 7, 8, 10, 11, etc and Windows Server. So you can use it to recover data from formatted SSD or other scenarios, such as accidental deletion, virus attacks, system crashes, etc.

Free download the best SSD data recovery software - MyRecover and install it. You can free recover deleted files up to 500MB. To recover unlimited files simultaneously, please upgrade MyRecover.

In order to recover as many of your data as possible, please connect SSD to another computer and perform SSD data recovery.

Step 1. Launch the best SSD data recovery software - MyRecover. Hover the mouse over the drive and click Scan to scan.

Step 2. The software will run Quick Scan and Deep Scan automatically. As soon as any deleted data is found, the tool will display it in the list. 

You can recover any file during the scanning process. To locate files faster, type the file name or type in the Search for files or folders box. To further narrow the scope, select Date modified and Size.

Step 3. Select the files you want to recover and click the Recover x files button to recover deleted files from SSD. You can recover any file during the scanning process.

Notes:

• Don’t try to recover files to its original location. This may overwrite previous data here and cause data recovery failure.
• It will display the number of files to recover and its total size.
• Except for SSD data recovery, you still can recover deleted files from USB, SD card and traditional hard drive.
• This software helps to recover deleted files Windows Server 2016, 2019, 2022, etc.

Approach Data Recovery Service When Necessary

Data recovery software helps to recover data from SSD disk but sometimes you need to seek help from professional data recovery service (such as CleverFiles). They have advanced equipment, technology, etc and work with data loss all the time.

• Your SSD has physical damage.
• Your SSD has a serious firmware failure and even upgrading the firmware won't help.
• Your SSD is experiencing a ransomware attack and cannot resolve it yourself.

To approach data recovery service, you just need to get in touch with a service provider. They will schedule a free consultation with you and quote the price. If you think it is reasonable, you can then ship your SSD drive to them. If they can’t, they return your SSD for free.

Common Signs of SSD Corruption

Unlike HDDs, SSDs does not have moving platter, so it is less likely to have mechanical failure. But there are some other factors affect your SSD:

🧰 Power failure: SSD requires a power capacitor and supplies, which are vulnerable, especially in power surge or power failure. Besides, the power failure will cause SSD data loss.

🏆 Limited or extremely slow read or write cycle: The limited read or write cycle is a issues with all kinds of flash memory. Be more care of it when you realize the read or write cycle is limited, especially it’s extremely slow. The SSD may be failing or failed.

❌Bad blocks: It’s much like bad sectors on HDDs and will affect data storage as well as retrieval function. If you SSD suffers from bad blocks, it may exhibit some of the following key symptoms.

• saving, reading and moving files takes unusual long time and result in failure.
• The active apps may crash frequently or become slowly.
• The general performance will decrease steadily, especially handing large files.
• ...

⚡ File system repair error: If you receive the file system repair error but physical defect software shows no damage, the connector port of SSD may have problem. It’s suggested to backup files before running any operations.

❤️‍🩹 Frequent crashes during boot: If your system crashes during the boot process but works fine after restarting times, then the SSD is probably failing. It might be a bad block or the sign of a dying drive, so please backup your data before losing any of them.

How to Fix a Failed SSD

The data recovery software is only available when your SSD is heath and can be recognized. If your SSD drive is failed, you could try the following 6 methods to fix it. But if the problem is caused by hardware damage or degraded flash cells, you need to replace SSD disk with a new one.

Method 1. Reconnect Your SSD

Sometimes, you can simply reconnect the failed SSD to make it recognized. Turn off your computer, disconnect the data and power cables and turn it on. Then, turn your computer off again, reconnect both cables and restart to Windows. Hope your SSD will come back.

Method 2. Power Cycling the SSD

Try this method if your SSD becomes corrupted due to power failure. First, unplug the SATA data cable but leave the power cable in. Keep this status for half an hour, and turn your computer off for 30 seconds. Then repeat this process. After that, reconnect the data cable and turn the power back on. Your SSD may come back at this point.

Method 3. Update SSD Firmware

The SSD firmware affects the drive’s ability to access, read and write data. If it’s damaged, you may also think the SSD is failed. You can choose to run a firmware update tool and check if there are latest firmware. Then, select and install the available update to see if your SSD function properly. Unfortunately, if the damage is more severe, even professionals cannot fix it.

Method 4. Update SSD Drivers

The SSD drivers also affect the SSD status if it work weirdly. You can try to update the SSD drivers and reconnect it.

Step 1. Press Win+R key, input devmgmt.msc and press OK to start Device Manager.

Step 2. Expand Disk drives and find the corrupted SSD disk. Right-click it and click Update drivers.

Step 3. Click Search automatically for drivers.

Step 4. Click Update drivers, it will automatically download and install SSD drivers.

Step 5. Restart your computer to make change take effect.

Method 5. Connect SSD to a Different Computer

Except for the SSD itself, it’s entirely possible that your operating system, or perhaps even your motherboard, is acting up. You can try to connect the failed SSD to another computer and check if the SSD is actually the cause.

Method 6. Format and reinstall Windows on SSD

If your operating system on SSD is failed, the fastest method is to format SSD and install Windows 10 on it. Or the latest operating system - Windows 11.

Format SSD in Windows Explorer

Step 1. Open Windows Explorer. Right-click the SSD and select Format...

Step 2. Uncheck Quick Format and click OK to format SSD completely.

Install Windows 10 on SSD

Step 1. Download Windows 10 Media Creation tool and start it up. Then, select Create installation media (USB flash drive, DVD, or ISO file) for another PC and follow the on-screen instructions to complete the media creation process.

Step 2. Connect the formatted SSD and installation media. Start your computer to BIOS and set the installation media as the first boot option. Press F10 to restart from it.

Step 3. Set language and other preferences and click Next. In the following screen, click Install Now.

Step 4. Skip the step to type product key.

Step 5. Select installation type - Custom and SSD drive to install Windows. Click Next and wait for the installation process to complete.

How to Keep SSD Always in Health Status

If you don't want to lose any data on SSD, please keep it always in health status. Here are suggestions you can follow:

• Move page files to a different disk.
• Turn off hibernation.
• Don’t run disk defragmentation on SSDs.
• Don’t full fill your SSD and overuse the swap space. To avoid this, you can choose to add more RAM to your system.
• Check the health of your SSD regularly, such as, the operating temperature or performance metrics.
• Keep your machines always cool.
• Invest in an SSD equipped with S.M.A.R.T. technology. It is capable of self-monitoring, analyzing and reporting potential failures, and prompting users to take preventive measures.
• Create a regular SSD data backup. The backup copy will include all the data on the SSD disk including the operating system. You can then restore disk from backup, whether your SSD fails or the data in it is lost.

Among them, the best practice is to backup SSD drive and data on it automatically with free backup software like AOMEI Backupper Standard. It not only preventS SSD failure & data loss but also gives you a chance to recover data from SSD quickly.

Step 1. Download and install Windows backup software - AOMEI Backupper Standard. Then, click Backup > Disk Backup to backup SSD disk and data on it.

Step 2. Set the Task Name to distinguish this backup task from others. Click Add Disk to choose your heath SSD disk.

Step 3. Select a location to store your SSD data. It can be internal or external disk, USB flash drive, network drive, NAS device, Cloud Drive, etc.

Step 4 (Optionally). Click Schedule Backup and enable Daily, Weekly, Monthly, Event triggers or USB plug in to backup SSD drive automatically.

Step 5. Click Start Backup to backup the entire SSD drive. By default, it will enable incremental backup to backup only new or changed data on SSD.

Frequently Asked Questions about SSD Data Recovery

✍ Why does SSD fail?

In general, there are three reasons account for this, namely, age, physical damage and heat. Among them, the most common reasons is heat. So please don’t let your device repeatedly overheats or left it in the hot sun.

✍ Is it harder to recover data from SSD?

The answer is yes, but not impossible. Many reports indicate the TRIM command greatly affect the SSD data recovery process. Because it will zero out or erase the space for “deleted” data immediately. It means your data are permanently deleted.

✍ How to recover data from a failing SSD

If you lose data on a failing SSD, you need to create sector by sector disk backup of the failing SSD and then use a data recovery software to recover from backup image. And this action can only be done once. If it is actually dead, try data recovery service.

✍ How to recover data from SSD that won’t boot

If your system does not boot, you can choose to disconnect the problematic SSD and connect it to another computer for SSD data recovery. Try the best recovery software - MyRecover.

✍ How to recover data from SSD with missing MBR

If your SSD does not have MBR, you are unable to boot your system. So the first thing is to rebuilt MBR. It requires a Windows installation media to access the recovery environment. 

Final Words

That’s all about how to recover data from an SSD drive in Windows 10 or 11. It also applies to Windows Server 2012, 2016, 2019, 2022, etc. Whether the TRIM command is enabled or not, the best data recovery software - MyRecover helps you.

In order not to lose any data, you need to take some measures to keep your SSD always health. Among them, creating a disk backup do a big favor. Because it keeps all of your data and give you a change to get your data back quickly.